NORYL  SE1 Resin datasheet
 

NORYL ™ Resin SE1

Europe-Africa-Middle East: COMMERCIAL

 
NORYL SE1 is an unfilled, flame retardant material with a Vicat B/120 of 140°C according ISO 306. NORYL SE1 is V1 at 1.47 mm according UL94 and halogen free according VDE/DIN 472 part 815.
 

Property
 
TYPICAL PROPERTIES (1)
MECHANICAL
Value Unit Standard
Tensile Stress, yield, 50 mm/min
55
MPa
ISO 527
Tensile Stress, break, 50 mm/min
50
MPa
ISO 527
Tensile Strain, yield, 50 mm/min
5
%
ISO 527
Tensile Strain, break, 50 mm/min
10
%
ISO 527
Tensile Modulus, 1 mm/min
2500
MPa
ISO 527
Flexural Stress, yield, 2 mm/min
90
MPa
ISO 178
Flexural Modulus, 2 mm/min
2300
MPa
ISO 178
Hardness, H358/30
95
MPa
ISO 2039-1
IMPACT
Value Unit Standard
Izod Impact, notched 80*10*4 +23°C
15
kJ/m²
ISO 180/1A
Izod Impact, notched 80*10*4 -30°C
7
kJ/m²
ISO 180/1A
Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm
15
kJ/m²
ISO 179/1eA
Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm
7
kJ/m²
ISO 179/1eA
THERMAL
Value Unit Standard
Thermal Conductivity
0.23
W/m-°C
ISO 8302
CTE, 23°C to 80°C, flow
7.E-05
1/°C
ISO 11359-2
CTE, 23°C to 80°C, xflow
8.E-05
1/°C
ISO 11359-2
Ball Pressure Test, 125°C +/- 2°C
PASSES
-
IEC 60695-10-2
Ball Pressure Test, approximate maximum
125
°C
IEC 60695-10-2
Vicat Softening Temp, Rate A/50
140
°C
ISO 306
Vicat Softening Temp, Rate B/50
130
°C
ISO 306
Vicat Softening Temp, Rate B/120
140
°C
ISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm
130
°C
ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm
120
°C
ISO 75/Ae
Relative Temp Index, Elec
110
°C
UL 746B
Relative Temp Index, Mech w/impact
105
°C
UL 746B
Relative Temp Index, Mech w/o impact
110
°C
UL 746B
PHYSICAL
Value Unit Standard
Mold Shrinkage on Tensile Bar, flow (2) (5)
0.5 - 0.7
%
SABIC Method
Density
1.11
g/cm³
ISO 1183
Water Absorption, (23°C/sat)
0.23
%
ISO 62
Moisture Absorption (23°C / 50% RH)
0.06
%
ISO 62
Melt Volume Rate, MVR at 280°C/5.0 kg
7
cm³/10 min
ISO 1133
ELECTRICAL
Value Unit Standard
Volume Resistivity
1.E+15
Ohm-cm
IEC 60093
Surface Resistivity, ROA
>1.E+15
Ohm
IEC 60093
Dielectric Strength, in oil, 0.8 mm
33
kV/mm
IEC 60243-1
Dielectric Strength, in oil, 1.6 mm
26
kV/mm
IEC 60243-1
Dielectric Strength, in oil, 3.2 mm
16
kV/mm
IEC 60243-1
Relative Permittivity, 1 MHz
2.7
-
IEC 60250
Dissipation Factor, 50/60 Hz
0.004
-
IEC 60250
Dissipation Factor, 1 MHz
0.002
-
IEC 60250
Comparative Tracking Index
200
V
IEC 60112
Relative Permittivity, 50/60 Hz
2.8
-
IEC 60250
FLAME CHARACTERISTICS
Value Unit Standard
UL Recognized, 94V-1 Flame Class Rating (3)
0.75
mm
UL 94
UL Recognized, 94V-0 Flame Class Rating (3)
6
mm
UL 94
Glow Wire Flammability Index 960°C, passes at
3.2
mm
IEC 60695-2-12
Oxygen Index (LOI)
31
%
ISO 4589
Source GMD, last updated:2002/07/15
Processing

Parameter
Injection Molding
Value Unit
Drying Temperature
80 - 100
°C
Drying Time
2 - 3
hrs
Melt Temperature
280 - 300
°C
Nozzle Temperature
260 - 280
°C
Front - Zone 3 Temperature
280 - 300
°C
Middle - Zone 2 Temperature
260 - 280
°C
Rear - Zone 1 Temperature
240 - 260
°C
Hopper Temperature
60 - 80
°C
Mold Temperature
90 - 120
°C
Source GMD, last updated:2002/07/15
 
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
 
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
(6) Needs hard coat to consistently pass 60 sec Vertical Burn.


Disclaimer : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES (“SELLER”) ARE SOLD SUBJECT TO SELLER’S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER’S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS.  UNLESS OTHERWISE PROVIDED IN SELLER’S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller’s materials, products, services or recommendations for the user’s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller’s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller.  Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.

 SABIC and brands marked with ™ are trademarks of SABIC or its subsidiaries or affiliates.

© 2014 Saudi Basic Industries Corporation (SABIC). All Rights Reserved.